Rubber & Tyre Machinery World

Info on Equipment And Suppliers


6 Comments

Why We Love Twin Screw Sheeter (And You Should, Too!)

Twin Screw Sheeter replaces the dump-mill and sheeting mill combination in a traditional rubber mixing line (an image you had seen in my earlier post – Single-Stage or Two-Stage Mixing?). This means you could visualize Twin Screw (Extruder) Sheeter, as a rubber machinery that accepts mix compound directly discharged from an internal mixer into its hopper chute and converts it into a continuous, seamless rubber sheet that is then fed into a Batch-Off Cooling Line.

For those who have been following my blog, you have already viewed a video of this equipment in action in my earlier post Rubber Mixing Room.

When you explore this equipment for purchase, you should not be surprised with different OEM’s calling it in similar sounding names. For example, you will get a Conical Twin Extruder (CTE) with Roller Head from Colmec SpATwin Screw Roller Head Extruder (TSR) from KobelcoTwin Screw Discharge Extruder (Convex™) from HF Mixing Group or simply Twin Screw Sheeter (TSS) from other rubber machinery manufacturers like Bainite Machines.

In construction, they all appear similar as shown below.

Kobelco Make TSR

Kobelco Make TSR with description

For reading simplicity, let me address this machinery simply as “TSS” for the rest of this article.

You will find the TSS to be ideal for conventional and diverse applications including tire manufacturing, custom compounding, hose & belt manufacturing and technical rubber goods production.

So, here’s why we love Twin Screw Extruder Sheeter (And, I feel, You Should, Too!).

  • Energy Saving: Rubber compounding is a energy-intensive process. So, any technological advancement that has the potential to reduce energy consumption receives my first preference (and I hope you will agree with me here). Let me help you with a quick back of the envelope calculation. If you are using a 270 Liter Tangential Internal Mixer, you are engaging at least two units of 26″x84″ two-roll mills in the downstream section. Each 26″x84″ two-roll mill, requires around 180 kW (minimum) motor power – totaling to 360 kW (=180 x 2) only for the mills. For a similar capacity mixer, a TSS downstream will not seek more than 300 kW power (again, there is energy-efficient models available here). So, this rough calculation, when a TSS replaces the traditional dump-mill with sheeting mill set up, straightaway gives you 16.7% savings in energy (60 kW less).
  • Labor: The second aspect is the reduction is labor cost. Unlike two-roll open mills (with or without ), where you will need two separate operators, a TSS can be set up to perform sheeting function of rubber sheet without an hands-on operator at its vicinity. Even if not fully automated, you do not need an operator once the discharge of rubber sheet from TSS is fed into a Batch-off.
  • Reduced Contamination: In open two-roll mixing mills, your rubber mixing is exposed to the environment and it is difficult to control any dirt or moisture absorption by the compound during milling process. In a TSS, this is eliminated. Your rubber and its recipe constituents are mixed and sheeted-out in a closed environment under temperature controlled conditions right from the time you feed it into your internal mixer. Hence, with reduced contamination, you get a guaranteed higher quality of your mix compound.
  • Self-Cleaning Feature: The Screw and Barrel of the TSS is at a downward inclination (15º) angle from the feed chute section to exit of the roller die head. This incline ensures that compound flow to the exit of the barrel is reinforced and no material remains inside the TSS – hence, the self-cleaning feature.
  • High Mixing Line Efficiency and Productivity: When you install a TSS , your compound batch from the internal mixer is converted into a continuous sheet and the working of TSS can be automatically synchronized with rubber mixing line speed. This in turn, improves the mixing line performance making it more efficient. The continuous sheeting without operator involvement increases your mixing line throughput and overall productivity. Original Equipment Manufacturers (OEM) can offer you customized TSS models beneath internal mixers with throughput capabilities from 500 Kg per hour to 21000 Kg per hour (….and that’s a vast range by all means).
  • Effective Temperature Control: Your rubber compound discharge temperatures from TSS is reduced while sheeting out the material because no additional work (hence no additional heat) is introduced into your compound. Additionally, there is circulation of tempered (or chilled) water inside the conical twin screws, barrel and the peripherally drilled rolls of the roller die. This flowing water facilitates an effective heat exchange to take away the heat from the rubber mix and reduces the compound temperature at the discharge sheeting section.
HF Twin Screw Extruder

HF Make Twin Screw Extruder

  • Compact Layout: Most manufacturers offer various drive options, making the design of the TSS very compact yet sturdy. This means that a TSS can be accommodated under most internal mixers starting from the lowest production range of 16-25 Liter capacities based on the OEM standards.
  • Easy Maintenance: Further, the screw tips of the energy-efficient conical twin-screws do not touch each other and hence there is minimized wear of the screws. A rapid action hydraulic cylinder arrangement for clamping and moving the roller-die calender on rails facilitates the cleaning of the screw tips and insides of the barrel tip during your scheduled maintenance. Also, the TSS does not require external pushers, as in case of single-screw dump extruders. These features make a TSS maintenance easy for you.
  • Additional Features: With increasing trend of Silica usage in rubber compounding, you need to be cautious of the metallurgy and surface treatment characteristics of any rubber compounding machinery you buy. Hence, explaining the major ingredients of your recipe to your OEM is of paramount importance. For example, in TSS you can seek rollers that has hard-surfaced rolls if you are processing silica compounds. This will minimize the compound sticking to the TSS roll and increase its life.

Lastly, this physically very sturdy and robust, rubber machinery is designed for intrinsically safe mixing line operation.

Summarizing, with its capabilities for conventional and diverse applications, a TSS is emerging as the standard downstream equipment in the rubber compounding process for masterbatch and final mixing lines. And that is why we love Twin Screw Sheeter.

How about you?


If you liked this article, please do share with your colleagues, customers and friends. And If you would like to be informed of our articles regularly, please register with us for free updates today.


10 Comments

Single-Stage or Two-Stage Mixing?

Have you encountered the often dilemma, “Should I do single-stage or two-stage mixing for my compound; which machinery to use?” – do not be surprised! You are not alone.

Single-stage mixing is considered for productivity reasons (and cost-effectiveness). While Two-stage mixing gives a better dispersion of the finer size blacks. And interestingly, for some compounds with high levels of blacks, even three or more mixing-passes may be necessary.

Rubber mixing as a subject would have been quite simpler, if we could answer this topic effortlessly. Unfortunately, it is not!

(Updated on 23rd Dec 2015: Flip through this post in our digital edition and download here)

Single-stage mixing in an internal mixer is a cost-effective solution but difficult for all compounds. If the compounds have high filler loadings, you may be forced to mix in two-stages due to the high amount of shear and heat generated in the mixing cycle. If you use peroxide cures or are mixing expensive FKM, then you must be even more worried of the batch temperature.

Most experts feel two-stage mixing, with short time spans for each of the mixing stages, is helpful.

One school of thought advocate an open two-roll mill for second-stage mixing because the dispersion of the batch and the mastication is higher (than an internal mixer). Open mills, though slower, are safe for short scorch compounds.

A traditional mixing line comprises of an internal mixer above a dump mill then one (or two) mill before the batch off cooling line.

Traditional Mixing Line with Two-Roll Mill Set-up

Reference Image Courtesy: Bainite Machines

Internal mixers are high-capacity rubber compounding machinery. Hence they need to be supported by open mills with advanced features to keep pace with production. The rotors of these mixers operate at high-speed to maximise dispersion of the bulk ingredients and dump the batch at high temperatures. Curatives, blowing agents, etc are added on the open mill and final homogenization happens on the last mill before batch off. Also, adding the cure system on downstream mill eliminates the batch contamination problem from “leftover’s” trapped (between the rotor end plates and ends of the rotors) in the internal mixer. These open mills are recommended to have peripherally drilled rolls to take out heat of the compound before adding heat sensitive curatives.

Open mill mixing is operator dependent and hence quality of compound varies from beginning of shift to end of shift. (Read about Stock Blender). As compared to rubber mixing in a closed environment, the probability of “fly loss” is high in open mills. Hence, an alternate school of thought propagates second-stage mixing also performed in an internal mixer. This can be at a lower speed, energy and dump-temperature configuration setting on mixer.

Single-stage mixing in an internal mixer is possible, when you mix and drop the batch within 120⁰C. The present range of internal mixers have advanced designs to effectively control batch temperature. With many designs and rotor geometries for faster mixing, accompanied by quicker cooling features, mixers like tandem mixers allow traditional two pass to be reduced to single pass cycle. (I will cover newer mixing lines with Twin Screw Sheeter, Dump Extruder, etc in different posts). As a side note, if you opt for single-stage mixing with internal mixer; the Intermeshing Type Mixer has the best quality and efficiency.

Single-stage mixing is not always cheaper and two-stage mixing is not always better. The best way to decide is to make a cost-benefit analysis between the two processes for the different polymers that you work with. Quantify how much of your product defects are linked to poor dispersion. Analyzing them, you have your customized solution to mix effectively.

Summarizing, there is no one best way for all compounds. Your mixing process has to be designed to the polymer; depends on the viscosity of the elastomers used, the quantity of filler, mixing temperature, machinery employed, time at every stage of mixing and desired physical properties for the end use product. If you get your “desired” characteristics in a single-stage mixing, adopt it or wisely opt for two-stage mixing.


If you liked this article, please do not forget to share with your colleagues and friends. And If you would like to be informed of our articles regularly, please register with us for free updates today.


1 Comment

Rubber Sheet Feeder

Internal Mixers and Mixing Mills are familiar rubber compounding machineries for short production runs. This is because of their broad range of shear capabilities and acceptance of all feed forms. Yet, rubber goods producers and tire manufacturers are familiar with their demerits viz. varying power demand, batch-to-batch quality variation and labor intensive operations.

Can you improve the experience and performance expectation? Yes, through the introduction of Sheet Feeders with Rotary Cutter.

Image Courtesy: Bainite Machines Pvt Ltd

Image Courtesy: Bainite Machines Pvt Ltd

Sheet feeders are designed for quick installation onto your existing layout. It could be either mounted to your Mixing Mill frame or put up in front of the weighing conveyor in a Mixer feed line. This means that space constraint never becomes an issue for you to extract more out of your existing mixing operations. And since only one operator can control the mill (or mixer) and sheet feeder, the operation does not increase your labor cost.

Sheet feeder’s with hugger belts replaces the conventional manual loading of rubber sheet on to the mill. This machine enhances your worker’s safety, and makes the loading operation safe. And because it facilitates continuous positive feed of the rubber sheets into the mill (or mixer), the operation feels ‘automatic’.

The rotary cutter on the sheet feeder cuts the fed rubber sheets into uniform rectangular pieces. This results in better dispersion of the rubber sheets in the mixing mill (or mixer for final batch).

The internal mixer rotors performs reactive, dispersive and distributive mixing of uniformly cut rubber sheets faster and better than a long sheet fed into the mixing chamber. The result you experience is a homogenized rubber mix, independent of the operator efficiency or any weight variations in the batch. The quicker mixing of the cut pieces shortens the mix cycle; thereby increasing the productivity of your internal mixer or mixing mill.

Summarizing, Sheet Feeders, is a simple machine which when installed to feed the mixing mill line or batch mixers, increases efficiency, reduces manual intervention and improves consistency of mix. This is also known as Mill Feeder, Rubber Feeder or Stock Loader with disc cutter.

Prodicon, Bainite Machines and few Chinese manufacturers offer them in the world market with customized specifications. Pelmar offers used-machinery of this category.

Please do let us know of your observations and notes on this allied machinery increasing efficiency into your existing rubber mixing line.


If you liked this article, please do not forget to share with your colleagues and friends. And If you would like to be informed of our articles regularly, please register with us for free updates today.